Residential · High Point, NC
A concrete patio should stay flat, drain correctly, and look clean for years, not chip at the edges or sink after one season. Quality Concrete High Point installs and repairs concrete patio slabs in High Point with proper base prep, control joints, and durable finishes built for daily foot traffic and outdoor furniture.
Prep makes or breaks a concrete patio. We start with layout, string lines, and grade checks, then excavate to remove soft topsoil and organics. A typical build includes 4 inches of 3,000 to 4,000 psi air-entrained concrete over a compacted stone base, often 4-6 inches of crushed stone (ABC or #57) compacted in lifts with a plate compactor. We use form boards, stakes, and diagonal measurements to keep the slab square, add a vapor barrier when needed, and set the slope away from the home so water does not pond at door thresholds.
Local clay soils and summer storms make drainage and joints especially important. We place rebar or welded wire mesh where the design and soil conditions call for it, then consolidate the mix, strike off, bull float, and edge the perimeter to reduce chipping. Control joints are planned to manage shrinkage cracking, typically spaced about 8-10 feet on a 4-inch slab, with joints cut or tooled at roughly one-quarter the slab thickness. Choose the finish that fits the space, broom-finish for slip resistance, light salt finish for texture, or stamped concrete with color hardener and a penetrating sealer for a higher-end look.
High Point customers choose us because we do the unglamorous work correctly, base, forms, slope, and joints, then finish clean. Since 2016 we have focused on residential and light commercial flatwork, and we show up with the right equipment for the job, plate compactors, screeds, floats, joint tools, and saws for timely joint cutting. You get clear options on thickness, reinforcement, and finish, plus a written estimate and a scope that spells out demo, haul-off, and site protection when replacing an existing concrete patio. Our crews work to consistent placement and curing practices so the slab gains strength evenly and the surface holds up to freeze-thaw cycles and de-icing salts.
Before we wrap up, we walk the slab with you and confirm drainage, joint layout, and edges at steps, walks, or existing slabs. For repairs, we identify the cause first, settlement, heaving, spalling, or poor drainage, then recommend the right fix, partial replacement, full tear-out and repour, or surface repair where appropriate. You receive straightforward care guidance, cure time before foot traffic and furniture, and sealing recommendations based on your finish. The result is a concrete patio that fits your space, meets grade, and is built to stay serviceable and easy to maintain.
Yes. We can break out old driveways, patios, and slabs, load debris, and haul it off before rebuilding the base and pouring new concrete.
Yes. We set grades and forms to tie into existing elevations, plan transitions, and maintain drainage so water does not run toward the garage or building.
Yes. You receive a written estimate that outlines demo (if needed), base, thickness, reinforcement, finish, and any saw-cut or joint plan.
Heavy rain, saturated subgrade, and temperature extremes can affect placement and finishing. We schedule pours around conditions that would compromise the slab, curing, or final finish.
Yes. We can build slabs for outbuildings and light commercial use, including thicker edges, reinforcement layouts, and anchor-bolt coordination when needed.
If your concrete patio is cracked, settled, or holding water, the problem is usually below the surface, weak base material, poor compaction, or incorrect slope. Quality Concrete High Point installs new patios and handles concrete patio repair with a build process that prioritizes grade, drainage, and joint planning, so the slab performs like it should. From small backyard pads to larger entertaining areas, we help you choose the right thickness, reinforcement, and finish for long-term durability.
A concrete patio is more than pouring a pad. We start by checking the subgrade and drainage path, then excavate to firm soil and build a stable base using crushed stone compacted in lifts. Forms are set to grade and slope, and we place a 3,000 to 4,000 psi air-entrained mix suitable for outdoor flatwork. During placement we strike off and float for a consistent plane, tool edges, and install control joints (tooled or saw-cut) to manage shrinkage and temperature movement. Proper curing helps reduce surface dusting and premature cracking, especially during hot, windy weather.
For concrete patio repair, we focus on the underlying cause. Spalling and surface scaling may point to freeze-thaw exposure, de-icers, or weak surface paste, while lifting or settling often traces back to poor base preparation or water movement. Depending on severity, the best solution may be a partial replacement, full tear-out and repour, or targeted patching for isolated damage. We will explain which option makes sense for your slab and budget, and when replacement is the more durable choice.
To finish the project, we verify drainage, confirm joint locations, and review cure times and maintenance. If you choose stamped or colored concrete, we discuss sealing and reseal intervals so the finish stays easier to clean and resists staining. When you want a concrete patio that feels level, drains correctly, and holds up to everyday use, our team delivers a straightforward process and a result you can trust.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in High Point. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.